Teltonika TRB500 Industrial Compact 5G Mobile Gateway
SKU# AC71800, Model# TRB500000200

Teltonika TRB500 Industrial Compact 5G Mobile Gateway - Ethernet: 1x Gigabit RJ45 - Power Connector: 4-pin industrial DC power socket - I/O: 2x Configurable I/O pins on 4-pin power connector, 1x SIM slot (Mini SIM 2FF), 4x SMA for Mobile, 1x Micro USB (for Virtual network) - Mounting Support: DIN rail, Flat surface - Routing: Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing - TRB500000200

Manufacturer Warranty: 2 Years Limited Warranty

Manufacturer Contact Info: https://teltonika.lt,

· 5G - Ultra-high cellular speeds of up to 1 Gbps

· SA & NSA - Supports both architectures to leverage the 5G infrastructure

· COMPACTNESS - One of the smallest 5G gateways available in the market

· FUTURE-PROOFING - Backward compatible with 4G (LTE CAT 20) and 3G network technologies

· Energy-efficient 5G gateway

TRB500 - INDUSTRIAL 5G GATEWAY

TRB500 is a compact, energy-efficient 5G gateway for ultra-fast data transmission with ultra-low latency. Backward compatibility with 4G and 3G networks enables future-proofing solution infrastructures even in areas where 5G is not yet available.

Features:

 

MOBILE

Mobile module - 5G Sub-6Ghz SA/NSA 2.1/3.3Gbps DL (4x4 MIMO), 900/600 Mbps UL (2x2); 4G (LTE) – LTE Cat 20 2.0Gbps DL, 200Mbps UL; 3G – 42 Mbps DL, 5.76Mbps UL

Status - Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID

SMS - SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

USSD - Supports sending and reading Unstructured Supplementary Service Data messages

Black/White list - Operator black/white list

Band management - Band lock, Used band status display

APN - Auto APN

Bridge - Direct connection (bridge) between mobile ISP and device on LAN

Passthrough - Gateway assigns its mobile WAN IP address to another device on LAN.

 

ETHERNET

Ethernet - 1 x ETH port, 10/100/1000 Mbps, supports auto MDI/MDIX crossover.

 

NETWORK

Routing - Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy-based routing

Network protocols - TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL)

VoIP passthrough support - H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring - Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall - Port forward, traffic rules, custom rules

Firewall status page - View all your Firewall statistics, rules, and rule counters

Ports management - View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on

Network topology - Visual representation of your network, showing which devices are connected to which other devices

Hotspot - Captive portal (Hotspot), internal/external Radius server, SMS authorisation, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, nine default customisable themes and option to upload and download customised hotspot themes

DHCP - Static and dynamic IP allocation, DHCP Relay

DDNS - Supported >25 service providers; others can be configured manually

Network backup - Mobile, VRRP, and Wired options, each of which can be used as an automatic Failover

SSHFS - Possibility to mount remote file system via SSH protocol

 

SECURITY

Authentication - Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block

Firewall - Pre-configured firewall rules can be enabled via WebUI, and unlimited firewall configuration via CLI, DMZ, NAT, and NAT-T.

Attack prevention - DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN - Port and tag-based VLAN separation

Mobile quota control - Mobile data limit, customisable period, start time, warning limit, phone number

WEB filter - Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control - Flexible access control of SSH, Web interface, CLI and Telnet

 

VPN

OpenVPN - Multiple clients and a server can run simultaneously, 27 encryption methods

OpenVPN Encryption - DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192, BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256

IPsec - IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)

GRE - GRE tunnel, GRE tunnel over IPsec support

PPTP, L2TP - Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

Stunnel - Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPN - Method of building scalable IPsec VPNs

SSTP - SSTP client instance support

ZeroTier - ZeroTier VPN client support

WireGuard - WireGuard VPN client and server support

Tinc - Tinc offers encryption, authentication and compression in its tunnels. Client and server support.

 

OPC UA

Supported modes - Client, Server (planned)

Supported connection types - TCP

 

MODBUS TCP SLAVE

ID range - Respond to one ID in the range [1;255] or any

Allow Remote Access - Allow access through WAN

Custom registers - MODBUS TCP custom register block requests, which read/write to a file inside the router and can be used to extend MODBUS TCP Slave functionality

 

MODBUS TCP MASTER

Supported functions - 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats - 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

 

DATA TO SERVER

Protocol - HTTP(S), MQTT, Azure MQTT, Kinesis

Data to server - Extract parameters from multiple sources and different protocols and send them all to a single server

 

MQTT GATEWAY

MQTT Gateway - Allows sending commands and receiving data from MODBUS Master through MQTT broker

 

DNP3

Supported modes - TCP Master, DNP3 Outstation

 

DLMS

DLMS Support - DLMS - standard protocol for utility meter data exchange

 

MONITORING & MANAGEMENT

WEB UI - HTTP/HTTPS, status, configuration, FW update, CLI, troubleshooting, event log, system log, kernel log

FOTA - Firmware update from server, automatic notification

SSH - SSH (v1, v2)

SMS - SMS status, SMS configuration, send/read SMS via HTTP POST/GET

Call - Reboot, Status, Mobile data on/off, Output on/off, answer/hang up with a timer

TR-069 - OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTT - MQTT Broker, MQTT publisher

SNMP - SNMP (v1, v2, v3), SNMP Trap

JSON-RPC - Management API over HTTP/HTTPS

MODBUS - MODBUS TCP status/control

RMS - Teltonika Remote Management System (RMS)

 

IOT PLATFORMS

Cloud of Things - Allows monitoring of Device data, Mobile data, Network info, and Availability.

ThingWorx - Allows WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, and Mobile Network Type monitoring.

Cumulocity - Allows monitoring of Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, and Signal Strength.

Azure IoT Hub - Can send device IP, Number of bytes sent/received, Temperature, PIN count to Azure IoT Hub server, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type.

 

SYSTEM CHARACTERISTICS

CPU - Single core ARM Cortex A7, 1.5 GHz

RAM - 256 MB (128 MB available for userspace)

FLASH storage - 512 MB (200 MB available for userspace)

 

FIRMWARE / CONFIGURATION

WEB UI - Update FW from a file, check FW on the server, configuration profiles, configuration backup

FOTA - Update FW

RMS - Update FW/configuration for multiple devices at once

Keep settings - Update FW without losing the current configuration

 

FIRMWARE CUSTOMISATION

Operating system - RutOS (OpenWrt based Linux OS)

Supported languages - Busybox shell, Lua, C, C++, Python, Java in Package Manager

Development tools - SDK package with build environment provided

GPL customisation - You can now create your own custom firmware and web page application, with some examples to make the creation process easier, and brand our firmware by changing colours, logos, and so on to fit your or your client’s needs.

 

INPUT / OUTPUT

Input - 1 x Digital Input, 0 - 6 V detected as logic low, 8 - 30 V detected as logic high

Output - 1 x Digital Output, Open collector output, max output 30 V, 300 mA

Events - Email, RMS, SMS

I/O juggler - Allows setting certain I/O conditions to initiate an event.

 

POWER

Connector - 4-pin industrial DC power socket

Input voltage range - 9 – 30 VDC, reverse polarity protection, surge protection +/-1 kV 50 µs max

Power consumption - Idle: < 3 W, Max < 6 W

 

PHYSICAL INTERFACES

Ethernet - 1 x RJ45 port, 10/100/1000 Mbps

I/O’s - 2 x Configurable I/O pins on 4-pin power connector

Status LEDs - 3 x connection type status LEDs, 3 x connection strength LEDs, 2 x LAN status LEDs, 1 x Power LED

SIM - 1 x SIM slot (Mini SIM – 2FF), 1.8 V/3 V

Power - 1 x 4-pin power connector

Antennas - 4 x SMA for Mobile

USB - 1 x Virtual network interface via micro USB

Reset - Reboot/User default reset/Factory reset button

 

PHYSICAL SPECIFICATION

Casing material - Aluminum housing

Dimensions - 100 x 30 x 93,4 mm

Weight - 241 g

Mounting options - DIN rail, Flat surface

 

OPERATING ENVIRONMENT

Operating temperature - -40 °C to 75 °C

Operating humidity - 10% to 90% non-condensing

Ingress Protection Rating - IP30

 

REGULATORY AND TYPE APPROVALS

Regulatory - CE, UKCA, RCM, CB, NBTC, RoHS, REACH

 

EMC EMISSIONS & IMMUNITY

Standards
EN 55032:2015 + A11:2020 + A1:2020
EN 55035:2017 + A11:2020
EN IEC 61000-3-2: 2019 + A1:2021
EN 61000-3-3: 2013 + A1:2019 + A2:2021
EN 301 489-1 V2.2.3
EN 301 489-52 V1.2.1

ESD - EN 61000-4-2:2009

Radiated Immunity - EN IEC 61000-4-3:2020

EFT - EN 61000-4-4:2012

Surge Immunity (AC Mains Power Port) - EN 61000-4-5:2014 + A1:2017

CS - EN 61000-4-6:2014

DIP - EN 61000-4-11:2020

 

RF

Standards

EN 301 908-1 V13.1.1
EN 301 908-2 V13.1.1
EN 301 908-13 V13.1.1
EN 301 908-25 V15.1.1_15.0.6

 

SAFETY

Standards

CE: EN IEC 62368-1:2020 + A11:2020, EN 62311:2020
RCM: AS/NZS 62368.1:2022
CB: IEC 62368-1:2018